Plaster and Drylining

Frequently Asked Questions

How long does plasterboard take to dry?

Plasterboard typically takes 24 to 48 hours to dry completely. However, the drying time can vary depending on the thickness of the plasterboard, the type of joint compound used, and the ambient temperature and humidity. In general, it's best to allow the plasterboard to dry for at least 24 hours before painting or sanding it.

Can you paint plasterboard?

Yes, you can paint plasterboard. It is made of a layer of gypsum sandwiched between two layers of heavy paper. Once the plasterboard has been installed and the joints have been taped and sanded, it can be painted just like any other type of wall.

How to cut plasterboard?

There are several ways to cut plasterboard, including using a utility knife, a drywall saw, or a circular saw. Here are some steps to follow when cutting plasterboard:

  1. Measure and mark the plasterboard where you need to make the cut. Use a straight edge or a ruler to draw a straight line along the cut mark.
  2. Use a utility knife to score the plasterboard along the cut line. Place the knife against the straight edge and apply steady, even pressure as you drag the knife along the line. The blade should go through the top paper layer and make a shallow cut in the gypsum layer.
  3. Once you have scored the plasterboard, use your hands to snap it along the cut line. Place your fingers on either side of the line and apply pressure to the plasterboard until it breaks cleanly along the line.
  4. If the cut is too long or too deep to snap by hand, use a drywall saw to finish the cut. A drywall saw has a thin, flexible blade that can easily follow the contours of the plasterboard. Place the saw blade on the cut line and saw through the plasterboard, using gentle back and forth motions.
  5. If you need to make a straight, precise cut, you can also use a circular saw. First, clamp a straight edge to the plasterboard to use as a guide for the saw. Then, adjust the saw blade to the appropriate depth and carefully cut along the straight edge. Be sure to wear ear and eye protection when using a circular saw.

Can you tile on plasterboard?

Yes, you can tile on plasterboard, but there are a few important considerations to keep in mind. It is made of a layer of gypsum sandwiched between two layers of heavy paper. While plasterboard is a good base for tiles, it is not as strong or durable as other materials like concrete or cement backer board. Therefore, it is important to take the necessary precautions to ensure that the tiles are properly supported and securely attached to the plasterboard.

Here are some steps to follow when tiling on plasterboard:

  1. Make sure the plasterboard is in good condition and properly installed. The surface should be smooth, flat, and free of cracks, holes, or other defects. If necessary, repair any damage and sand the surface smooth before proceeding.
  2. Use a thin-set adhesive specifically designed for tiling on plasterboard. This type of adhesive is more flexible and less likely to crack than regular mortar.
  3. Apply the adhesive to the plasterboard in small sections, using a notched trowel. Spread the adhesive evenly, making sure to cover the entire surface.
  4. Begin installing the tiles, starting at the center of the wall and working outward. Use a level to ensure that the tiles are straight and evenly spaced.
  5. Use plastic tile spacers to maintain consistent grout lines. Once the tiles are in place, allow the adhesive to cure according to the manufacturer's instructions.
  6. Once the adhesive has fully cured, apply grout to the joints between the tiles. Use a grout float to push the grout into the joints, making sure to fill all the gaps. Wipe away any excess grout with a damp sponge.
  7. Once the grout has dried, apply a grout sealer to protect it from stains and moisture. This will help to prevent the grout from cracking or crumbling over time.
  8. In conclusion, while it is possible to tile on plasterboard, it is important to use the right adhesive, tools, and techniques to ensure that the tiles are securely attached and the installation is durable.

How thick is plasterboard?

Plasterboard is typically sold in sheets, and the thickness of the sheets can vary. The most common thicknesses for plasterboard are 9.5 mm, 12.5 mm, and 15 mm. These measurements refer to the thickness of the plasterboard panel, not including the paper facing on either side. The thickness of the plasterboard you choose will depend on the type of application and the amount of support required. In general, thicker plasterboard is more durable and provides better sound insulation, but it is also more expensive and heavier to handle.

How do you fill holes in plasterboard?

To fill holes in plasterboard, you will need some filler or joint compound, a putty knife, a sanding block, and some primer and paint (optional). Here is a simple step-by-step guide:

  1. Use the putty/filling knife to apply a generous amount of filler or joint compound into the hole, making sure to fill it completely.
  2. Smooth the surface of the filler or joint compound using the putty knife, and allow it to dry completely according to the manufacturer's instructions.
  3. Once the filler or joint compound has dried, use a sanding block to sand the area until it is smooth and flush with the surrounding wall.
  4. If desired, apply a coat of primer to the repaired area and allow it to dry.
  5. Finally, paint the repaired area to match the surrounding wall.

What is dot and dab?

Dot and dab is a method of fixing plasterboard or drywall to a wall. It involves applying dabs of adhesive, or "dots," to the back of the plasterboard or drywall and then pressing it firmly onto the wall. This creates a strong bond between the plasterboard or drywall and the wall, and allows the plasterboard or drywall to be securely fixed in place without the need for nails or screws.

The dot and dab method is commonly used when installing plasterboard or drywall on masonry or concrete walls, as it provides a strong and secure fixing that is less likely to fail than a fixing using nails or screws. It is also often used in situations where it is not possible or practical to fix the plasterboard or drywall to the wall using nails or screws, such as when the wall is made of a material that is not suitable for fixing with nails or screws.

Don't miss out!

Sign up for our email list for exclusive deals, new products & events. Be the first to know & eligible for special promotions. Don't miss out, sign up today!

Thank you for your submission! You will hear from us soon.